Bell 47D1 crash near Pell City, AL, United States

HISTORY OF FLIGHT On January 21, 2014, about 1537 central standard time, a Bell 47D-1, N93067, operated by Milam Inc. was substantially damaged during a forced landing near Pell City, Alabama. The commercial pilot and one passenger received minor injuries. Day, visual meteorological conditions prevailed, and no flight plan was filed for the business flight, operated under the provisions of Title 14 Code of Federal Regulations Part 91, which originated at Birmingham- Shuttlesworth International Airport (BHM), Birmingham, Alabama about 1330. According to the pilot, after meeting his passenger at BHM at 1300 they flew to an area just outside of Pell City, Alabama to look at a newly installed alarm system and to take some aerial photographs of the customer's property. After flying around the property which covered approximately 100 acres, and discussing how they could take the photographs, they landed and retrieved a camera from the "chin area" of the helicopter. The pilot then discussed with the passenger how he could fly along the borders of the property so the passenger could take the photographs he desired. They then departed and flew "the plan" they had discussed, and then returned to the spot where they had landed before. While descending into the confined area for landing, at 25 to 35 feet above ground level, the pilot heard a "snap/pop" and the engine suddenly began "over-revving." The helicopter began descending, and due to the undulating terrain that was below them the pilot could only extend the flight slightly forward, and within approximately 3 seconds, he had used up all of the available rotor speed. The helicopter then touched down hard and one of the wooden main rotor blades struck the tail of the helicopter. The engine was still running but with no rotor motion. The pilot then shutoff the magnetos and battery switches, and he and the passenger exited the helicopter. PERSONNEL INFORMATION According to Federal Aviation Administration (FAA) and pilot records, the pilot held a commercial pilot certificate with ratings for helicopter, airplane single-engine land, Airplane multi-engine land, and instrument airplane, with private pilot privileges for airplane single-engine sea. He also held a flight instructor certificate with a rating for helicopters, and repairman experimental aircraft builder certificate, with an inspection certificate for an experimental Rotorway Executive helicopter he had built. His most recent FAA second-class medical certificate was issued on April 4, 2013. He reported that he had accrued 4,430 total hours of flight experience, 1,086 of which were in make and model. AIRCRAFT INFORMATION The accident aircraft was two-bladed, single engine, light helicopter which according to the FAA registry was manufactured by Bell Helicopter Company in 1965 as a Bell model 47D-1, serial number 5501. According to maintenance records, the helicopter's most recent annual inspection was completed on June 9, 2013. At the time of accident, the helicopter had accrued approximately 3,980 total hours of operation. Bell 47 History and Build Records On March 8, 1946, the Bell 47 was certificated for civilian use by the Civil Aeronautics Administration. More than 5,600 were produced with the helicopter being manufactured in the United States, and under license in Italy, Japan, and the United Kingdom. Review of Bell Helicopter Company build records by Scott's-Bell 47, which purchased the type certificate from Bell Helicopter Textron in 2010, revealed that despite what was recorded in the FAA registry, the accident helicopter was not built by Bell Helicopter Company or any of its licensees. According to build records, at the time that the accident helicopter was listed as being manufactured in 1965, Bell Helicopter was manufacturing two production blocks of helicopters, with serial numbers 3958 through 4013, being built as OH-13 models for the United States Army, and serial numbers 6501 thru 6513, being built as 47G-3B-1 models, for the commercial market. Bell produced no helicopters during that time period bearing serial numbers within the gap (4014 thru 6500) which existed between the two production blocks, which would have encompassed manufacturer's serial number 5501. Further review of build records also revealed that no civilian Bell Model 47 was ever delivered bearing the serial number 5501 by Bell, nor were there any military Bell helicopter models similar to the model 47 under any year of manufacture, that would have been assigned a sequential serial number and/or military ship number by Bell or the military services, which would have consisted of the 2-digit year of manufacture, and military serial number that could have been similar to the 5501 serial number on the accident helicopter. FAA Certification Data Review of FAA Type Certificate Data Sheets (TCDS) and a search of FAA's Electronic Data Retrieval System (EDRS) revealed that with Federal Aviation Agency (Successor to the CAA, which later became the Federal Aviation Administration under the Department of Transportation) approval, a number of entities "manufactured" helicopters from Bell spare and surplus parts, which the Federal Aviation Agency issued airworthiness certificates for, and then classified as Bell 47s in the registry, though Bell had not manufactured them as the type certificate holder. These included approximately: - 20 entities who had manufactured Bell 47D-1 models. - 16 entities who had manufactured Bell 47G models. - 9 entities who had manufactured Bell 47G-2 models. Further review of FAA TCDS and FAA EDRS data indicated that a helicopter manufactured as a 47D-1 bearing serial number 5501, was listed as an aircraft eligible for designation as a 47D-1, under the name of Louis Wm. Cottriel. Identification (Data) Plate According to the FAA, Each manufacturer of aircraft, aircraft engines, propellers, and propeller blades and hubs is required to display the following information on a fireproof plate, by means of stamping, engraving, etching, or another approved method: (1) The builder's name, which may be the name of an individual, firm, co-partnership, corporation, company, association, or joint-stock association. (2) Model designation. (3) Builder's serial number. (4) TC number, if any. (5) Production certificate (PC) number, if any. (6) For aircraft engines, the established rating. (7) For aircraft engines, the date of manufacture, that is, month (two digits)/ year (four digits). (8) For aircraft engines, the engine's approved 14 CFR part 34 designations. (Part 34 discusses fuel venting and exhaust emission requirements for turbine engine-powered airplanes.) Approved designations include comply, exempt, and non-U.S. for engines specified in part 34, manufactured on or after January 1, 1984. The fireproof plate is required to be placed on a surface where it is not likely to be defaced or removed during normal service. The identification cannot be placed on an inspection plate, or removable fairing. On aircraft manufactured before March 7, 1988, the identification plate is required to be mounted on an interior or exterior location near an entrance, so that it is legible from the ground either just behind and next to the rear-most entrance door or on the underside of the fuselage near the tail surface. The model and serial numbers also are required to be displayed on the fuselage exterior. In regards to identification plate requirements for aircraft built from spare or surplus parts, In addition, to the requirements listed above, the following guidelines should be followed: (1) Use the builder's name as the name (the person who assembled the aircraft), not the name of the manufacturer who builds the same model of aircraft. (2) Assign any serial number if it is clear that the manufacturer who builds the same model of aircraft did not assign an identical number. A letter prefix or suffix should also be added such as a